Home

MTCUME

Modulo 1

  • PPP Profile
  • Local and remote addresses
  • Incoming and outgoing filters
  • Address list
  • Change TCP-MSS
  • Use encryption
  • Session timeout
  • Rate-limit configuration
  • Only-one setting
  • PPP Secret
  • Service and Profile
  • Local and Remote address
  • Routes configuration
  • Limit Bytes In/Limit Bytes Out configuration IP Pool
  • Set addresses ranges
  • Next pool options
  • Module 1 laboratory

Modulo 2

  • PPTP and L2TP
  • Theory • Comparison
  • PPTP Client configuration
  • Client setup
  • Set profile
  • Dial on demand
  • Add default route and static routes
  • PPTP Server configuration
  • Enable server
  • Setup profiles
  • Add clients to PPP secret
  • Set static interfaces for clients
  • L2TP Client configuration
  • Client setup
  • Configure profile
  • Dial on demand
  • Add default route and static routes
  • L2TP Server configuration
  • Enable server
  • Set profiles
  • Add clients to PPP secret
  • Set Static interfaces for clients
  • Module 2 laboratory

Modulo 3

  • PPPoE server and client (Theory • Usage environment • Comparison to other PPP protocols)
  • PPPoE client configuration ( Client setup • Select interface • Service name • Configure profile)
  • PPPoE Server configuration (Enable PPPoE server • Set profiles • Add clients to PPP secret • Add Static interfaces for clients • Secure server by removing any IP address from PPPoE server interface)
  • Encryption (Set profile without encryption • Set profile with encryption • Configure PPPoE client without encryption)
  • Interface ECMP (Set ECMP routes for PPP interfaces)
  • Module 3 laboratory

Modulo 4

  • L2TP and EoIP (Set L2TP tunnel • Set EoIP tunnel • Create bridge and add necessary interfaces to ports • Confirm you have Ethernet connectivity between remote nodes)
  •  L2TP and VPLS ( Set L2TP tunnel • Set VPLS tunnel • Create bridge and add necessary interfaces to ports)
  • L2TP and BCP (Set L2TP tunnel • Use BCP to bridge PPP interface • Add to bridge necessary interface)
  • Multilink Protocol (Enable multilink by specifying correct MRRU settings • Disable mangle rules for MSS adjustment)
  • MLPPP (optional) (Setup client and specify multiple interfaces for one client • Set PPPoE server with MLPPP support )
  • Module 4 laboratory

Modulo 5

  • Introduction (Theory and concepts • Comparison to other VPN protocols )
  • IPSec Peer (Use different authentication methods • IPSec exchange modes • Encryption and hash algorithms • NAT-Traversal • Lifetime and lifebytes • DPD protocol )
  • Policy (IPSec protocol and action • Tunnels • Generate dynamic Policy)
  • Proposal (Encryption and authentication algorithms • Lifetime • PFS )
  • Installed-SA (Flush SA)
  • Create IPSec between two routers with NAT(Set peer • Set policy • Set NAT rules • Confirm the secure link is established)
  • Module 5 laboratory

Modulo 6

  •  Introduction( Concepts • Usage environments • Setup HotSpot with default settings)
  • HotSpot Login Methods (HTTP CHAP/PAP • MAC • Cookie • HTTPS • Trial • RADIUS)
  • Users (Add users • Set MAC-address for user • Set MAC-address for username)
  • Limit Uptime and Limit Bytes In/Out (Reset limits for user )
  • Monitor Users (Host Table • Active Table • SNMP for users)
  • Profile (Keepalive timeout • Shared users • Rate-Limit • Address-list • Incoming/Outgoing filter • Incoming/Outgoing Packet Mark)
  • Bypass HotSpot (Walled garden • Walled garden IP • IP binding)
  • Customize HotSpot (Advertisement • Customize pages)
  • Module 6 laboratory

Modulo 7

  • RADIUS client (Add radius client • Set service • Use RADIUS for the specific service)
  • RADIUS server
  • User manager (Install the latest user-manager • Add routers • Add users • Set profile)
  • RADIUS incoming
  • Module 7 laboratory

Alejandro Teixeira

Francisco Mendez

 

Duración: 16 horas

Dirigido a :

Administradores de red, jefes de sistemas y Operadores

Nivel : Inicial

Requisitos:

Certificados en MTCNA

Horario:

Disponemos de cómodos horarios a su elección